Landing (procedures) - Revision history

Stefanido: Landing Procedures moved to Landing (procedures)

2010-04-20T16:35:16Z

Landing Procedures moved to Landing (procedures)

Rubberchickenben: bryn, procedures don't need introductions

2008-10-05T03:32:30Z

bryn, procedures don't need introductions

Burn at 16:08, 2 October 2008

2008-10-02T16:08:29Z

Burn at 16:06, 2 October 2008

2008-10-02T16:06:49Z

TheKillerRabbit: Added links

2007-06-28T01:07:00Z

Added links

TheKillerRabbit: Messed up NextTopic

2007-06-27T20:57:51Z

Messed up NextTopic

TheKillerRabbit: Created

2007-06-27T20:57:14Z

Created

New page

====1.5.9 Landing Procedure====
# Select Status: TARGET (toggle Tab key)
#* Choose Target as the current planet (press key from Table 1.5.A)
# Select Status: REFERENCE (toggle Tab key)
#* choose Reference for orbital maneuvers as current planet (press key from Table 1.5.A)
# Select Status: CENTRE (toggle Tab key)
#* choose centre view point as the current planet (press key from Table 1.5.A)
# Magnify image (+ - keys) to see the current planet clearly
# Toggle F5 to bring up the AYSE docking systems control panel.
# Arm and Unlock the AYSE docking latches.
# Activate the AYSE UNDOCKING process.
# Wait until undocking is complete and the Auto Docking status shows RED.
# Set Thermal Control Measures to OFF.
# Press 'v' key to activate the approach velocity vector if not done already.
# Fire the reverse engine (use a low thrust setting (-1 to -5 m/s/s) until the approach velocity vector points directly towards the centre of the target.
# Press F4 for automatic depart from target orientation.
# Press F1 for manual orientation.
# Increase thrust (regular thrust (positive) not reverse thrust) using ']' key until the A to targ matches the engine thrust.
# Increase engine thrust to slow Vhab-ref speed to something appropriate (a value of about 10% of the distance value (D to targ) may work).
# Reduce thrust to match A to targ value.
# If the landing is taking too long, adjust thrust to increase Vhab-ref, but this make it harder to stop.
#* '''If A-targ value exceed 50 m/s/s''' then:
#** @ Low Altitude: maintain maximum thrust and brace for hard landing
#** @ High Altitude: Initiate Landing Abort Procedure P1.5.13
# If the approach velocity vector starts to point away from the centre of the target, rotate the AYSE drive slightly in the opposite direction to correct it then re-adjust the orientation to stabilize the approach velocity vector.
# As you get closer to the target, gravity will increase the A to targ value and you must increase thrust to match it.
# As you get closer to the planet, use increased thrust to slow down and readjust thrust to match A to targ.
# When distance reads 0.00, stop engine.

{{Procedure|PrevTopic='''[[Orbital Maneuvering Procedures]]'''
|PrevNum=1.5.8
|ThisTopic='''Landing Procedures'''
|ThisNum=1.5.9
|NextTopic='''[[Landing Procedures]]'''
|NextNum=1.5.10}}

@@ Line 1: / Line 1: @@
 ====1.5.9 Landing Procedure====
-Instructions for landing the [[Habitat]] in the pilot program [[Orbit|ORBIT]]
+Instructions for landing the [[Habitat]] in the pilot program [[Orbit|ORBIT]].
 # Select Status: TARGET (toggle Tab key)
 #* Choose Target as the current planet (press key from [[Table 1.5.A]])

← Older revision	Revision as of 16:35, 20 April 2010
(No difference)

@@ Line 1: / Line 1: @@
 ====1.5.9 Landing Procedure====
 # Select Status: TARGET (toggle Tab key)
-#* Choose Target as the current planet (press key from Table 1.5.A)
+#* Choose Target as the current planet (press key from [[Table 1.5.A]])
 # Select Status: REFERENCE (toggle Tab key)
-#* choose Reference for orbital maneuvers as current planet (press key from Table 1.5.A)
+#* choose Reference for orbital maneuvers as current planet (press key from [[Table 1.5.A]])
 # Select Status: CENTRE (toggle Tab key)
-#* choose centre view point as the current planet (press key from Table 1.5.A)
+#* choose centre view point as the current planet (press key from [[Table 1.5.A]])
 # Magnify image (+ - keys) to see the current planet clearly
 # Toggle F5 to bring up the AYSE docking systems control panel.
@@ Line 22: / Line 22: @@
 #* '''If A-targ value exceed 50 m/s/s''' then:
 #** @ Low Altitude: maintain maximum thrust and brace for hard landing
-#** @ High Altitude: Initiate Landing Abort Procedure P1.5.13
+#** @ High Altitude: Initiate [[P1.5.13]]
-# If the approach velocity vector starts to point away from the centre of the target, rotate the AYSE drive slightly in the opposite direction to correct it then re-adjust the orientation to stabilize the approach velocity vector.
+# If the approach velocity vector starts to point away from the centre of the target, rotate the [[AYSE Drive]] slightly in the opposite direction to correct it then re-adjust the orientation to stabilize the approach velocity vector.
 # As you get closer to the target, gravity will increase the A to targ value and you must increase thrust to match it.
 # As you get closer to the planet, use increased thrust to slow down and readjust thrust to match A to targ.

@@ Line 33: / Line 33: @@
 |ThisTopic='''Landing Procedures'''
 |ThisNum=1.5.9
-|NextTopic='''[[Landing Procedures]]'''
+|NextTopic='''[[Planetary Launch Procedures]]'''
 |NextNum=1.5.10}}